Why Pallet Wood Earns Its Place in the Garden
Pallet wood has a lot going for it. It is usually free, it is already weathered to a soft grey that suits cottage and contemporary gardens alike, and the slats are a handy size for knocking together a decent-sized planter in an afternoon. Most pallets are made from softwood such as pine or spruce, with the occasional hardwood slat thrown in, and that is perfectly good for a garden box that will hold compost rather than a car engine.
Before you load up the boot, check the stamp burned into the pallet's side. Look for HT, which means heat treated, and that is the one you want. Avoid anything marked MB, as this has been fumigated with methyl bromide, and steer clear of pallets that have clearly carried chemicals, oil drums or dyed powders. A faint smell of creosote or a suspicious stain means leave it where it is.
Breaking Down the Pallets and Smoothing Rough Edges
Dismantling a pallet is the bit that separates a pleasant morning's work from a trip to A&E, so take it slowly. A flat pry bar or a dedicated pallet buster makes short work of the slats, and a claw hammer deals with the stubborn ones. Work from the underside where possible and rock the bar rather than forcing it, which reduces the chance of splitting the timber. Wear gloves throughout — pallet wood splinters are vicious and often carry grit.
Once the slats are free, pull or punch out every remaining nail. A nail left in a board will wreck a saw blade and can catch a hand later. Then tackle the surfaces properly:
- Start with 60 to 80 grit paper on an orbital sander to knock back splinters, raised grain and grubby patches.
- Follow with 120 grit to leave a surface you can run a hand along without wincing.
- Ease the sharp arrises along every edge with a few passes, as bare corners are where splinters live.
- Brush dust out of the grain with a stiff brush, and blow out any knot holes.
Do not sand to a polished finish. A slightly open surface takes wood preserver far better than a burnished one.
Building a Planter That Will Not Twist
A simple square or rectangular box works best, roughly 50cm across and 35 to 40cm deep. That depth gives roots room without making the planter impossibly heavy to move once filled. Cut the slats to length and arrange them horizontally, leaving a 5mm gap between boards for a little airflow.
Line the slats up against a pair of internal corner battens — 40mm square is ideal — and screw through from the outside. Use stainless steel or coated decking screws, around 4 x 40mm, because ordinary steel screws will rust and stain the timber within a season. Two screws per slat end is plenty.
For anything wider than 60cm, add a central batten or a horizontal brace across the back to stop the sides bowing out once the compost is wet and pressing against them. Give the base a slatted floor of boards laid with 10mm gaps so water can escape freely, then sit the whole thing on two timber bearers or bricks. Raising it off the ground keeps the base dry and dramatically extends its life.
Treating the Timber for Years Outdoors
Untreated softwood left in the damp will start to soften within a couple of years, so treatment is not optional. Brush on a solvent-based or water-based wood preserver, paying particular attention to end grain, which soaks up moisture like a straw. Two coats, with the first allowed to dry properly before the second goes on, is the minimum.
Once the preserver has cured, finish with a decking oil or a garden furniture oil to shed water. If you would rather the planter silver down naturally, a clear water-repellent treatment will do the job while letting the timber weather. Avoid creosote and any product not labelled as safe for plants, and if you are growing edibles, choose a treatment marked suitable for use around fruit and vegetables.
Lining, Filling and Planting Up
Compost straight against bare timber will keep it permanently damp, and damp timber rots. Line the inside of the planter with a porous membrane such as a woven landscape fabric, which lets water through but keeps compost away from the wood. A butyl or EPDM liner is a better choice if you are growing thirsty plants, though you will then need to drill drainage holes in the base and cover them with a scrap of membrane to stop them silting up.
Staple the liner to the top inside edge, trim it neatly, and leave the top 2cm of timber exposed so water does not track behind the lining. Then build up the layers:
- A 5cm layer of gravel or broken crocks in the base for drainage.
- A thin layer of garden soil or well-rotted compost mixed with grit to stop the gravel silting up.
- Fill to within 3cm of the rim with a decent peat-free multipurpose compost, or a soil-based mix for shrubs and perennials that will stay put for years.
- Firm gently as you go, leaving the surface slightly loose so water soaks in rather than running off.
Water thoroughly after planting, then keep the compost consistently moist but never waterlogged for the first season. Trailing herbs, nasturtiums, compact roses or a mix of hardy perennials all do well, and a planter built from salvaged timber always looks better with something slightly unruly spilling over its edges.

Comments