Breaking

Site add
blog single post
Upcycling

Upcycling a Pine Chest of Drawers

Why Old Pine Deserves a Second Chance

Pine chests of drawers turn up everywhere — charity shops, car boot sales, the back of a relative's garage. They are usually solid, generously sized and built from proper timber rather than chipboard, which is more than can be said for a lot of what you'll find on the high street today. The problem is that pine as a finish has fallen badly out of fashion. That honeyed orange varnish, the knobbly grain, the odd knot weeping resin down a drawer front: it all dates a piece horribly.

But strip that back and you have a blank canvas. A chest of drawers is one of the easiest pieces of furniture to upcycle because it is made of flat panels, has few awkward curves, and comes apart into manageable sections. A weekend's work and around £30–£60 of materials will give you something that looks like it came from a decent interiors shop.

What You'll Need Before You Start

Decent preparation matters far more than expensive paint, so gather everything in one go and save yourself the mid-job dash to the shops.

  • A random orbital sander plus 80, 120 and 180 grit discs. A sanding block and sheets for the fiddly bits.
  • Knotting solution — essential on pine. Any knot left untreated will bleed brown stains through your lovely new paint within weeks.
  • A shellac-based or adhesion primer, not a water-based one. Water-based primers raise the grain on pine and can let resin through.
  • Matt paint — a hard-wearing water-based eggshell in matt or a specialist furniture paint. Avoid standard matt emulsion on its own; it marks badly.
  • Filler, a filling knife, and fine-grade surface filler for old handle holes.
  • A foam mini roller and a decent synthetic brush. Rollers leave a flatter finish than brushing alone.
  • New handles, plus a tape measure, pencil and drill.
  • Dust sheets, a mask, and plenty of old rags.

Empty, Strip and Sand

Take the drawers out and remove every handle, knob and backplate. Pop them into a jar so nothing goes astray — you can often reuse the original screws. If the drawers have metal runners, unscrew those too; it makes sanding the carcase far easier.

Start with 80 grit on the flattest surfaces. You are not trying to remove every trace of colour, just to key the surface, knock off any flaking varnish and open up the grain so the primer can grip. Work with the grain and keep the sander moving, because pine is soft and it is very easy to dish a drawer front if you linger in one spot.

Move up to 120 grit, then finish with 180. Anything coarser than 180 will show through paint as scratches. For the mouldings and corners, wrap a sheet around a cork block and go over the shape by hand.

Wipe everything down with a damp cloth and let it dry completely. Once dry, brush knotting solution over every knot you can see — front, back and inside. Two thin coats on any knot that is still weeping.

Repairs Worth Doing Now

While the chest is bare, sort out the small faults you'd otherwise regret later.

  • Wobbly joints: squeeze wood glue into the gap and clamp overnight. If you don't own clamps, a ratchet strap around the whole carcase works a treat.
  • Sticking drawers: rub a candle or a block of beeswax along the runners and the bottom edges of the drawer sides. It's an old trick and it genuinely works.
  • Old handle holes: fill with two-part wood filler, leave proud of the surface, then sand flush once fully cured.
  • Split or chipped edges: build up thin layers of filler rather than one thick blob, which will shrink and crack.

Prime and Paint

Give the whole piece one coat of shellac-based primer, applied thinly with the roller and brushed into the corners. It dries fast — usually under an hour — and it smells, so open a window or work in the garage. Once dry, sand very lightly with 240 grit to knock back any raised fibres, then dust off.

Now the paint. Stir it thoroughly rather than shaking, which introduces bubbles. Apply two or three thin coats rather than one thick one. Roll a small section, then immediately lay it off lightly with a dry brush to flatten the roller texture. Work in the direction of the grain where you can.

Leave the recommended drying time between coats — usually two to four hours for water-based paint — and don't be tempted to rush it. Paint that hasn't cured will drag and look patchy. If you are painting the drawer fronts a different colour, remove them and paint them flat on a table so nothing runs down the edges.

Finishing Touches and New Handles

Wait at least 24 hours before refitting the hardware, longer if the weather is damp or humid. Position your new handles by measuring from the centre of each drawer and marking the hole centres with a bradawl. Drill a pilot hole slightly narrower than the screw, or you'll split the pine — especially on narrower drawer fronts. Keep a scrap of timber behind the drawer front when you drill through, to stop the wood blowing out on the reverse.

If your new handles have different centre measurements to the old ones, don't panic: fill the old holes, sand flush, touch in with primer and paint, and drill fresh. Slightly wider centres usually suit a wide drawer better anyway.

Finally, line the drawer bases with a remnant of wallpaper or some self-adhesive lining. It takes ten minutes and makes the inside feel as considered as the outside. Then refit the drawers, rub a little wax on the runners, and stand back. A chest that was heading for the tip now has decades of use left in it.

Comments